Robot Metal Jumbo Chassis Black High Quality is brand new palletized Powder coated with scratch and corrosion-resistant metal body chassis for small DIY hobby projects purpose with readymade 4 holes for motor fitting on its side edge and 1 hole at the top for wiring purpose.This Chassis board is widely used as a mechanical frame structure of the mobile robots. It is the backbone of the robot, where we arrange and connect everything like motors, sensors, and wheels. It gives you the base to build our robot and allow you to place your components according to requirements.
-22%
Robot Metal Jumbo Chassis Black (Pack of 1)
₹249.00 ₹194.00
Categories: B2B, BASIC ELECTRONIC COMPONENTS, ELECTRONIC COMPONENTS, ELECTRONICS ACCESSORIES, KITS
Additional information
Weight | 0.250 kg |
---|---|
Dimensions | 6 × 4 × 3 cm |
Reviews (0)
Be the first to review “Robot Metal Jumbo Chassis Black (Pack of 1)” Cancel reply
You may also like…
Chassis Kit – Chassis + Gear Motor Robot Wheel + 200 Rpm Gear Motor | Robotics Science Project (7 X 4 Cm Wheels)
ELECTRONIC COMPONENTS, BASIC ELECTRONIC COMPONENTS, ELECTRONICS ACCESSORIES, KITS, ROBOT KITS, B2B, ELECTRONIC MODULES
Related products
LM393 LM393DR SOP-8 SMD LOW POWER VOLTAGE COMPARATOR (PACK OF 10)
₹249.00
220uf 50v Electrolytic Capacitor (Pack of 10)
7805 5v voltage regulator (Pack of 10)
₹24.00
EL817 Optocoupler SMD PIN-4 (Pack of 10)
Burg Stick 40 Pin Pcb Male Pin Header Strip Connector ( Pack of 10)
Capacitor 470uf 35v Aluminium Electrolytic (Pack of 10)
Wireless Transceiver Module NRF24L01+ 2.4GHZ – for Arduino MCU/ARM/PIC/AVR/STM32 (Pack of 1)
wireless Transceiver module is an easy and suitable module if you want to setup your wireless communication system with low cost!! This module can achieve a good balance between wireless transition performance and cost!Only require an external inductor in the antenna matching There is no need multi-layer PCB. 5V tolerance level inputs. Improved ShockBurst and the serial interface can be easy to connect with a variety of low-cost MCU. There si no need SPI interface with the MCU. Received in the rate of 2Mbit/s, the peak current is 12.5mA.You can easily add it with your own MCU/ARM/PIC/AVR/STM32 system! 2Mbit/s, 1Mbit/s, 250Kbit/s, three selectable transmission rate. MultiCeiver hardware and six receiver functions. 2 Mbit/s make high-quality VoIP is possible. +/- 60 ppm crystal.When the rate of 2Mbit/s @ 0dBm output,the peak current is 11mA. Power-down mode, power consumption is 400nA. Standby mode, power consumption is 32uA. 130us fast switching and wake time.With voltage regulator:Oltage regulators on board. Built-in
5mm Diffused Led Pack-basic-ultimatum, Light Emitting Diode (Pack of 10)
ELECTRONIC COMPONENTS, BASIC ELECTRONIC COMPONENTS, ELECTRONICS ACCESSORIES, LED | PLUGS / CONNECTORS, ROBOT KITS, B2B
Tsop 38 Mhz Ir Receiver Pcb Remote Control Sensor Module Microcontroller (Pack of 10)
2 Pin Pcb Mount Screw Terminal Block Connectors 128 (Pack of 10)
Active Buzzer Module (3.3-5V) For arduino Arm Avr Pic – (Pack of 1)
Drv8825 Stepper Motor Driver with Aluminum Heat Sink
BOARDS, CONTROLLERS, ELECTRONICS ACCESSORIES, KITS, KITS, MECHANICAL ROBOTIC PARTS, MOTORS, ROBOT KITS, B2B, ELECTRONIC COMPONENTS, ELECTRONIC MODULES
100uf 100v Electrolytic Capacitors (Pack of 10)
Nano Board CH 340/ATmega+328P Without USB Cable, Compatible with Arduino Nano V3.0(PACK OF1)
ELECTRONIC COMPONENTS, BASIC ELECTRONIC COMPONENTS, ELECTRONICS ACCESSORIES, LEARNING AND ROBOTIC KITS, ROBOT KITS, B2B
Reviews
There are no reviews yet.