A trimpot or trimmer potentiometer is a small potentiometer which is used for adjustment, tuning and calibration in circuits. When they are used as a variable resistance (wired as a rheostat) they are called preset resistors. Trimpots or presets are normally mounted on printed circuit boards and adjusted by using a screwdriver.
-30%
10K PRESET FOR BREADBOARD AND ARDUINO PROTOTYPING (MAKE BOURNS) (Pack of 10)
Rated 2.00 out of 5 based on 1 customer rating
(1 customer review) ₹249.00 ₹175.00
Ordered:0
Items available:50
In stock
SKU: 231222
Categories: BASIC ELECTRONIC COMPONENTS, ELECTRONIC COMPONENTS
Additional information
Weight | 0.250 kg |
---|---|
Dimensions | 6 × 5 × 3 cm |
Reviews (1)
1 review for 10K PRESET FOR BREADBOARD AND ARDUINO PROTOTYPING (MAKE BOURNS) (Pack of 10)
Add a review Cancel reply
You may also like…
12x12x13mm Tactile Push Button Switch (PACK OF 10)
Related products
Active Buzzer Module (3.3-5V) For arduino Arm Avr Pic – (Pack of 1)
M7 1000v 1a Rectifier Diode Smd (Pack of 10)
2 Pin Pcb Mount Screw Terminal Block Connectors 128 (Pack of 10)
El817 Evelight Optocoupler Ic Dip-4 (Pack of 10)
Rocker Switch 3 P DPST On/Off/On I/O/II Switch –
ELECTRONIC COMPONENTS, BASIC ELECTRONIC COMPONENTS, BOARDS, DRONE PARTS, CONTROLLERS, ELECTRONICS ACCESSORIES, KITS, KITS, POWER SUPPLY, ROBOT KITS, B2B, ELECTRONIC MODULES
EL817 Optocoupler SMD PIN-4 (Pack of 10)
Capacitor Aluminium Electrolytic 47uf 100v Sk-47uf/100v (Pack of10)
Rated 4.00 out of 5
Digit 7 Segment Led Display Common Cathode (Pack of 10)
Durable Rubber Robot Tire, Yellow Wheel 65mmx30mm For Bo Dc Motor (Pack of 4)
7805 5v voltage regulator (Pack of 10)
₹24.00
6 * 8CM 1.6mm 2.54mm Pitch Double-Side Prototype PCB Universal Printed Circuit Board
470uf 16v Electrolytic Capacitor (Pack of 10)
Wireless Transceiver Module NRF24L01+ 2.4GHZ – for Arduino MCU/ARM/PIC/AVR/STM32 (Pack of 1)
wireless Transceiver module is an easy and suitable module if you want to setup your wireless communication system with low cost!! This module can achieve a good balance between wireless transition performance and cost!Only require an external inductor in the antenna matching There is no need multi-layer PCB. 5V tolerance level inputs. Improved ShockBurst and the serial interface can be easy to connect with a variety of low-cost MCU. There si no need SPI interface with the MCU. Received in the rate of 2Mbit/s, the peak current is 12.5mA.You can easily add it with your own MCU/ARM/PIC/AVR/STM32 system! 2Mbit/s, 1Mbit/s, 250Kbit/s, three selectable transmission rate. MultiCeiver hardware and six receiver functions. 2 Mbit/s make high-quality VoIP is possible. +/- 60 ppm crystal.When the rate of 2Mbit/s @ 0dBm output,the peak current is 11mA. Power-down mode, power consumption is 400nA. Standby mode, power consumption is 32uA. 130us fast switching and wake time.With voltage regulator:Oltage regulators on board. Built-in
Marlene –
This article iss acftually a good one iit hewlps new the webb people,
who are wishing in favoir oof blogging.
Also visit myy wbpage … Randy